Will the Anker SOLIX PS100 Bifacial work with the Jackery HomePower 1000 v2?
Yes. One Anker SOLIX PS100 Bifacial works with the Jackery HomePower 1000 v2: about 28.4 V on a 20°F morning against the station's 60 V limit, and about 100 W in full sun. Two panels: works (1 panel on DC8020 + 1 panel on DC8020), about 200 W.
Works
1 x PS100 Bifacial into the HomePower 1000 v2 (1 panel on DC8020) stays inside 16 to 60 V and under 12 A, even at 20F.
- The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number.
- Needs an MC4 to DC8020 adapter cable.
100 W, open-circuit 25.9 V, short-circuit 4.9 A, working 21.6 V / 4.6 A. Unconfirmed Panel details
Jackery HomePower 1000 v2Solar input DC8020: 16 to 60 V; DC8020: 16 to 60 V, 400 W max. Manual Station details
Change the count or temperatureTwo panels: every way to wire them
| Wiring | Input | Volts at 20F | Amps | Watts | Verdict |
|---|---|---|---|---|---|
| 1 panel on DC8020 + 1 panel on DC8020 The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number. | DC8020 + DC8020 | 28.4 | 4.6 | 200 | Works |
| 2 panels in parallel on DC8020 The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number. | DC8020 | 28.4 | 9.3 | 200 | Works |
| 2 panels in series on DC8020 The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number. | DC8020 | 56.7 | 4.6 | 200 | Works |
Quick answers
Will the Anker SOLIX PS100 Bifacial work with the Jackery HomePower 1000 v2?
Yes. One Anker SOLIX PS100 Bifacial works with the Jackery HomePower 1000 v2: about 28.4 V on a 20°F morning against the station's 60 V limit, and about 100 W in full sun. Two panels: works (1 panel on DC8020 + 1 panel on DC8020), about 200 W.
Can I connect two PS100 Bifacial panels to the HomePower 1000 v2?
Yes, 1 panel on DC8020 + 1 panel on DC8020. That gives about 200 W.
What cable do I need to connect the PS100 Bifacial to the HomePower 1000 v2?
Needs an MC4 to DC8020 adapter cable.
Is it safe on a cold morning?
Panel voltage rises in the cold. One PS100 Bifacial goes from 25.9 V on its label to about 28.4 V at 20°F and 29.2 V at 0°F. The HomePower 1000 v2 accepts up to 60 V on the DC8020.
Where to buy
We may earn a commission if you buy through these links. It never changes a verdict.
Other panels that work with the HomePower 1000 v2
- Jackery HomePower 1000 v2: solar input 16 to 60 V on the Solar in 1 (DC8020). Jackery does not say whether this limit is open-circuit or working voltage, so we use the stricter reading: open-circuit voltage on your coldest morning.
- Cold raises panel voltage: we add 0.30% per °C below 77F (25°C), a typical figure, since this panel does not publish its own. At 20F one panel's 25.9 V becomes 28.4 V.
- Current over the 12 A cap is safe: the station takes 12 A and you get fewer watts. We count only the capped watts.
- Max 200 W on this input, 400 W across all inputs.
- Cold-morning voltage uses 0.30% per °C, typical for crystalline panels. This panel's own value is not published.
- Expected watts are the best case in full sun. Real-world midday output is usually 60 to 80% of that.
- Some numbers for Anker SOLIX PS100 Bifacial come from a shop listing we have not confirmed in the manual yet.