Will the EcoFlow NextGen 220W Bifacial Portable Solar Panel work with the EcoFlow DELTA Pro 3?
Yes. One EcoFlow NextGen 220W Bifacial Portable Solar Panel works with the EcoFlow DELTA Pro 3: about 23.5 V on a 20°F morning against the station's 60 V limit, and about 219 W in full sun. Two panels: works (2 panels in series on XT60 (High-PV)), about 438 W.
Works
1 x NextGen 220W Bifacial Portable Solar Panel into the DELTA Pro 3 (1 panel on XT60i (Low-PV)) stays inside 11 to 60 V and under 20 A, even at 20F.
- The two solar inputs are different. High-PV takes 30 to 150V, Low-PV takes 11 to 60V. A single small panel is too low for High-PV and will not charge there.
- EcoFlow's manual: panel voltage rises in cold weather, so keep a margin below the limit when wiring in series.
- For parallel wiring you need Y-branch (T-branch) solar cables.
- Use an MC4 to XT60i solar cable.
220 W, open-circuit 21.5 V, short-circuit 12.4 A, working 18.4 V / 11.9 A. Brand page Panel details
EcoFlow DELTA Pro 3Solar input XT60 (High-PV): 30 to 150 V; XT60i (Low-PV): 11 to 60 V, 2600 W max. Manual Station details
Change the count or temperatureTwo panels: every way to wire them
| Wiring | Input | Volts at 20F | Amps | Watts | Verdict |
|---|---|---|---|---|---|
| 2 panels in series on XT60 (High-PV) Best option | XT60 (High-PV) | 47.1 | 11.9 | 438 | Works |
| 2 panels in series on XT60i (Low-PV) | XT60i (Low-PV) | 47.1 | 11.9 | 438 | Works |
| 2 panels in parallel on XT60i (Low-PV) The panels can push 23.8A but this input takes 20A, so the station caps it. Safe, you just lose some watts. | XT60i (Low-PV) | 23.5 | 23.8 | 368 | Works |
| 1 panel on XT60 (High-PV) + 1 panel on XT60i (Low-PV) Open-circuit voltage 21.5V is below the 30V minimum for this input, so it will not start charging. | XT60 (High-PV) + XT60i (Low-PV) | 23.5 | 11.9 | 0 | Don't connect |
| 2 panels in parallel on XT60 (High-PV) Open-circuit voltage 21.5V is below the 30V minimum for this input, so it will not start charging. | XT60 (High-PV) | 23.5 | 23.8 | 0 | Don't connect |
Quick answers
Will the EcoFlow NextGen 220W Bifacial Portable Solar Panel work with the EcoFlow DELTA Pro 3?
Yes. One EcoFlow NextGen 220W Bifacial Portable Solar Panel works with the EcoFlow DELTA Pro 3: about 23.5 V on a 20°F morning against the station's 60 V limit, and about 219 W in full sun. Two panels: works (2 panels in series on XT60 (High-PV)), about 438 W.
Can I connect two NextGen 220W Bifacial Portable Solar Panel panels to the DELTA Pro 3?
Yes, 2 panels in series on XT60 (High-PV). That gives about 438 W.
What cable do I need to connect the NextGen 220W Bifacial Portable Solar Panel to the DELTA Pro 3?
Use an MC4 to XT60i solar cable.
Is it safe on a cold morning?
Panel voltage rises in the cold. One NextGen 220W Bifacial Portable Solar Panel goes from 21.5 V on its label to about 23.5 V at 20°F and 24.3 V at 0°F. The DELTA Pro 3 accepts up to 60 V on the XT60i (Low-PV).
Where to buy
We may earn a commission if you buy through these links. It never changes a verdict.
Other panels that work with the DELTA Pro 3
- EcoFlow DELTA Pro 3: solar input 11 to 60 V on the Solar in 2 (XT60i (Low-PV)). EcoFlow sets this limit on open-circuit voltage (Voc), so we hold the panels' Voc on your coldest morning to it.
- Cold raises panel voltage: we add 0.30% per °C below 77F (25°C), a typical figure, since this panel does not publish its own. At 20F one panel's 21.5 V becomes 23.5 V.
- Current over the 20 A cap is safe: the station takes 20 A and you get fewer watts. We count only the capped watts.
- Max 1,000 W on this input, 2,600 W across all inputs.
- Cold-morning voltage uses 0.30% per °C, typical for crystalline panels. This panel's own value is not published.
- Expected watts are the best case in full sun. Real-world midday output is usually 60 to 80% of that.