Will the BLUETTI SP200L Solar Panel work with the Anker SOLIX C1000 Gen 2?
Yes. One BLUETTI SP200L Solar Panel works with the Anker SOLIX C1000 Gen 2: about 26.9 V on a 20°F morning against the station's 60 V limit, and about 200 W in full sun. Two panels: works (2 panels in parallel on XT60i), about 400 W.
Works
1 x SP200L Solar Panel into the C1000 Gen 2 (1 panel on XT60i) stays inside 11 to 60 V and under 14.5 A, even at 20F.
- The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number.
- Anker's page gives 11 to 60V but does not say whether that is open-circuit or working voltage, so the checker uses the stricter reading.
- BLUETTI does not publish the working voltage (Vmp) or current (Imp) for this panel.
- Use an MC4 to XT60i solar cable.
200 W, open-circuit 24.6 V, short-circuit 10.8 A. Brand page Panel details
Anker SOLIX C1000 Gen 2Solar input XT60i: 11 to 60 V, 600 W max. Brand page Station details
Change the count or temperatureTwo panels: every way to wire them
| Wiring | Input | Volts at 20F | Amps | Watts | Verdict |
|---|---|---|---|---|---|
| 2 panels in parallel on XT60i The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number. | XT60i | 26.9 | 21.6 | 400 | Works |
| 2 panels in series on XT60i The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number. | XT60i | 53.9 | 10.8 | 400 | Works |
Quick answers
Will the BLUETTI SP200L Solar Panel work with the Anker SOLIX C1000 Gen 2?
Yes. One BLUETTI SP200L Solar Panel works with the Anker SOLIX C1000 Gen 2: about 26.9 V on a 20°F morning against the station's 60 V limit, and about 200 W in full sun. Two panels: works (2 panels in parallel on XT60i), about 400 W.
Can I connect two SP200L Solar Panel panels to the C1000 Gen 2?
Yes, 2 panels in parallel on XT60i. That gives about 400 W.
What cable do I need to connect the SP200L Solar Panel to the C1000 Gen 2?
Use an MC4 to XT60i solar cable.
Is it safe on a cold morning?
Panel voltage rises in the cold. One SP200L Solar Panel goes from 24.6 V on its label to about 26.9 V at 20°F and 27.8 V at 0°F. The C1000 Gen 2 accepts up to 60 V on the XT60i.
Where to buy
We may earn a commission if you buy through these links. It never changes a verdict.
Other panels that work with the C1000 Gen 2
- Anker SOLIX C1000 Gen 2: solar input 11 to 60 V on the Solar in (XT60i). Anker SOLIX does not say whether this limit is open-circuit or working voltage, so we use the stricter reading: open-circuit voltage on your coldest morning.
- Cold raises panel voltage: we add 0.30% per °C below 77F (25°C), a typical figure, since this panel does not publish its own. At 20F one panel's 24.6 V becomes 26.9 V.
- Current over the 14.5 A cap is safe: the station takes 14.5 A and you get fewer watts. We count only the capped watts.
- Max 600 W on this input.
- Cold-morning voltage uses 0.30% per °C, typical for crystalline panels. This panel's own value is not published.
- Expected watts are the best case in full sun. Real-world midday output is usually 60 to 80% of that.