Will the Jackery SolarSaga 200 (JS-200E) work with the Anker SOLIX C1000 Gen 2?
Yes. One Jackery SolarSaga 200 (JS-200E) works with the Anker SOLIX C1000 Gen 2: about 23.9 V on a 20°F morning against the station's 60 V limit, and about 200 W in full sun. Two panels: works (2 panels in series on XT60i), about 400 W.
Works
1 x SolarSaga 200 (JS-200E) into the C1000 Gen 2 (1 panel on XT60i) stays inside 11 to 60 V and under 14.5 A, even at 20F.
- The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number.
- Anker's page gives 11 to 60V but does not say whether that is open-circuit or working voltage, so the checker uses the stricter reading.
- Needs a DC8020 to XT60 adapter. Neither brand sells this pairing, so check any third-party adapter is rated for the current.
200 W, open-circuit 22 V, short-circuit 12.5 A, working 18 V / 11.5 A. Manual Panel details
Anker SOLIX C1000 Gen 2Solar input XT60i: 11 to 60 V, 600 W max. Brand page Station details
Change the count or temperatureTwo panels: every way to wire them
| Wiring | Input | Volts at 20F | Amps | Watts | Verdict |
|---|---|---|---|---|---|
| 2 panels in series on XT60i The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number. | XT60i | 47.8 | 11.5 | 400 | Works |
| 2 panels in parallel on XT60i The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number. | XT60i | 23.9 | 23 | 261 | Works |
Quick answers
Will the Jackery SolarSaga 200 (JS-200E) work with the Anker SOLIX C1000 Gen 2?
Yes. One Jackery SolarSaga 200 (JS-200E) works with the Anker SOLIX C1000 Gen 2: about 23.9 V on a 20°F morning against the station's 60 V limit, and about 200 W in full sun. Two panels: works (2 panels in series on XT60i), about 400 W.
Can I connect two SolarSaga 200 (JS-200E) panels to the C1000 Gen 2?
Yes, 2 panels in series on XT60i. That gives about 400 W.
What cable do I need to connect the SolarSaga 200 (JS-200E) to the C1000 Gen 2?
Needs a DC8020 to XT60 adapter. Neither brand sells this pairing, so check any third-party adapter is rated for the current.
Is it safe on a cold morning?
Panel voltage rises in the cold. One SolarSaga 200 (JS-200E) goes from 22 V on its label to about 23.9 V at 20°F and 24.5 V at 0°F. The C1000 Gen 2 accepts up to 60 V on the XT60i.
Where to buy
We may earn a commission if you buy through these links. It never changes a verdict.
Other panels that work with the C1000 Gen 2
- Anker SOLIX C1000 Gen 2: solar input 11 to 60 V on the Solar in (XT60i). Anker SOLIX does not say whether this limit is open-circuit or working voltage, so we use the stricter reading: open-circuit voltage on your coldest morning.
- Cold raises panel voltage: we add 0.27% per °C below 77F (25°C), this panel's own figure. At 20F one panel's 22 V becomes 23.9 V.
- Current over the 14.5 A cap is safe: the station takes 14.5 A and you get fewer watts. We count only the capped watts.
- Max 600 W on this input.
- Cold-morning voltage uses this panel's own coefficient from its manual, 0.27% per °C.
- Expected watts are the best case in full sun. Real-world midday output is usually 60 to 80% of that.