Will the Anker SOLIX PS100 Bifacial work with the Goal Zero Yeti 3000X?
Yes. One Anker SOLIX PS100 Bifacial works with the Goal Zero Yeti 3000X: about 28.4 V on a 20°F morning against the station's 50 V limit, and about 100 W in full sun. Two panels: works (1 panel on High Power Port + 1 panel on 8mm), about 200 W.
Works
1 x PS100 Bifacial into the Yeti 3000X (1 panel on High Power Port) stays inside 14 to 50 V and under 50 A, even at 20F.
- The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number.
- Goal Zero gives solar charging as 600 W actual input at most, across its ports.
- Needs an MC4 to HPP (Anderson Powerpole) adapter cable.
100 W, open-circuit 25.9 V, short-circuit 4.9 A, working 21.6 V / 4.6 A. Unconfirmed Panel details
Goal Zero Yeti 3000XSolar input High Power Port: 14 to 50 V; 8mm: 14 to 50 V, 600 W max. Brand page Station details
Change the count or temperatureTwo panels: every way to wire them
| Wiring | Input | Volts at 20F | Amps | Watts | Verdict |
|---|---|---|---|---|---|
| 1 panel on High Power Port + 1 panel on 8mm The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number. | High Power Port + 8mm | 28.4 | 4.6 | 200 | Works |
| 2 panels in parallel on High Power Port The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number. | High Power Port | 28.4 | 9.3 | 200 | Works |
| 2 panels in parallel on 8mm The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number. | 8mm | 28.4 | 9.3 | 150 | Works |
| 2 panels in series on High Power Port Open-circuit voltage 51.8V is above the station's 50V limit. Going over a station's input voltage limit can damage it. | High Power Port | 56.7 | 4.6 | 0 | Don't connect |
| 2 panels in series on 8mm Open-circuit voltage 51.8V is above the station's 50V limit. Going over a station's input voltage limit can damage it. | 8mm | 56.7 | 4.6 | 0 | Don't connect |
Quick answers
Will the Anker SOLIX PS100 Bifacial work with the Goal Zero Yeti 3000X?
Yes. One Anker SOLIX PS100 Bifacial works with the Goal Zero Yeti 3000X: about 28.4 V on a 20°F morning against the station's 50 V limit, and about 100 W in full sun. Two panels: works (1 panel on High Power Port + 1 panel on 8mm), about 200 W.
Can I connect two PS100 Bifacial panels to the Yeti 3000X?
Yes, 1 panel on High Power Port + 1 panel on 8mm. That gives about 200 W.
What cable do I need to connect the PS100 Bifacial to the Yeti 3000X?
Needs an MC4 to HPP (Anderson Powerpole) adapter cable.
Is it safe on a cold morning?
Panel voltage rises in the cold. One PS100 Bifacial goes from 25.9 V on its label to about 28.4 V at 20°F and 29.2 V at 0°F. The Yeti 3000X accepts up to 50 V on the High Power Port.
Where to buy
We may earn a commission if you buy through these links. It never changes a verdict.
Other panels that work with the Yeti 3000X
- Goal Zero Yeti 3000X: solar input 14 to 50 V on the Solar in 1 (High Power Port). Goal Zero does not say whether this limit is open-circuit or working voltage, so we use the stricter reading: open-circuit voltage on your coldest morning.
- Cold raises panel voltage: we add 0.30% per °C below 77F (25°C), a typical figure, since this panel does not publish its own. At 20F one panel's 25.9 V becomes 28.4 V.
- Current over the 50 A cap is safe: the station takes 50 A and you get fewer watts. We count only the capped watts.
- Max 600 W on this input, 600 W across all inputs.
- Cold-morning voltage uses 0.30% per °C, typical for crystalline panels. This panel's own value is not published.
- Expected watts are the best case in full sun. Real-world midday output is usually 60 to 80% of that.
- Some numbers for Anker SOLIX PS100 Bifacial come from a shop listing we have not confirmed in the manual yet.