Will the Renogy 250W N-Type Bifacial Solar Panel work with the Goal Zero Yeti 300?
Yes. One Renogy 250W N-Type Bifacial Solar Panel works with the Goal Zero Yeti 300: about 24.5 V on a 20°F morning against the station's 28 V limit, and about 195 W in full sun. Two panels: works (2 panels in parallel on 8mm), about 195 W.
Works
1 x 250W N-Type Bifacial Solar Panel into the Yeti 300 (1 panel on 8mm) stays inside 12.3 to 28 V, even at 20F. The station caps the current at 10 A.
- The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number.
- The panels can push 12.8A but this input takes 10A, so the station caps it. Safe, you just lose some watts.
- Goal Zero says a 200 W panel needs its HPP to 8mm connector for this station.
- Needs an MC4 to 8mm adapter cable.
250 W, open-circuit 22.4 V, short-circuit 13.5 A, working 19.5 V / 12.8 A. Brand page Panel details
Goal Zero Yeti 300Solar input 8mm: 12.3 to 28 V, 200 W max. Brand page Station details
Change the count or temperatureTwo panels: every way to wire them
| Wiring | Input | Volts at 20F | Amps | Watts | Verdict |
|---|---|---|---|---|---|
| 2 panels in parallel on 8mm The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number. | 8mm | 24.5 | 25.6 | 195 | Works |
| 2 panels in series on 8mm Open-circuit voltage 44.7V is above the station's 28V limit. Going over a station's input voltage limit can damage it. | 8mm | 48.9 | 12.8 | 0 | Don't connect |
Quick answers
Will the Renogy 250W N-Type Bifacial Solar Panel work with the Goal Zero Yeti 300?
Yes. One Renogy 250W N-Type Bifacial Solar Panel works with the Goal Zero Yeti 300: about 24.5 V on a 20°F morning against the station's 28 V limit, and about 195 W in full sun. Two panels: works (2 panels in parallel on 8mm), about 195 W.
Can I connect two 250W N-Type Bifacial Solar Panel panels to the Yeti 300?
Yes, 2 panels in parallel on 8mm. That gives about 195 W.
What cable do I need to connect the 250W N-Type Bifacial Solar Panel to the Yeti 300?
Needs an MC4 to 8mm adapter cable.
Is it safe on a cold morning?
Panel voltage rises in the cold. One 250W N-Type Bifacial Solar Panel goes from 22.4 V on its label to about 24.5 V at 20°F and 25.2 V at 0°F. The Yeti 300 accepts up to 28 V on the 8mm.
Where to buy
We may earn a commission if you buy through these links. It never changes a verdict.
Other panels that work with the Yeti 300
- Goal Zero Yeti 300: solar input 12.3 to 28 V on the Solar in (8mm). Goal Zero does not say whether this limit is open-circuit or working voltage, so we use the stricter reading: open-circuit voltage on your coldest morning.
- Cold raises panel voltage: we add 0.30% per °C below 77F (25°C), a typical figure, since this panel does not publish its own. At 20F one panel's 22.4 V becomes 24.5 V.
- Current over the 10 A cap is safe: the station takes 10 A and you get fewer watts. We count only the capped watts.
- Max 200 W on this input.
- Cold-morning voltage uses 0.30% per °C, typical for crystalline panels. This panel's own value is not published.
- Expected watts are the best case in full sun. Real-world midday output is usually 60 to 80% of that.