Will the BLUETTI PV350D work with the Goal Zero Yeti 1500X?
Yes. One BLUETTI PV350D works with the Goal Zero Yeti 1500X: about 36.1 V on a 20°F morning against the station's 50 V limit, and about 350 W in full sun. Two panels: works (2 panels in parallel on High Power Port), about 600 W.
Works
1 x PV350D into the Yeti 1500X (1 panel on High Power Port) stays inside 14 to 50 V and under 50 A, even at 20F.
- The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number.
- Goal Zero gives solar charging as 600 W actual input at most, across its ports.
- The panel's plug type is not confirmed yet. Check the label or the box before buying a cable.
350 W, open-circuit 33 V, short-circuit 13.8 A, working 27.6 V / 12.7 A. Manual Panel details
Goal Zero Yeti 1500XSolar input High Power Port: 14 to 50 V; 8mm: 14 to 50 V, 600 W max. Brand page Station details
Change the count or temperatureTwo panels: every way to wire them
| Wiring | Input | Volts at 20F | Amps | Watts | Verdict |
|---|---|---|---|---|---|
| 2 panels in parallel on High Power Port The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number. | High Power Port | 36.1 | 25.4 | 600 | Works |
| 1 panel on High Power Port + 1 panel on 8mm The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number. | High Power Port + 8mm | 36.1 | 12.7 | 500 | Works |
| 2 panels in parallel on 8mm The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number. | 8mm | 36.1 | 25.4 | 150 | Works |
| 2 panels in series on High Power Port Open-circuit voltage 66V is above the station's 50V limit. Going over a station's input voltage limit can damage it. | High Power Port | 72.3 | 12.7 | 0 | Don't connect |
| 2 panels in series on 8mm Open-circuit voltage 66V is above the station's 50V limit. Going over a station's input voltage limit can damage it. | 8mm | 72.3 | 12.7 | 0 | Don't connect |
Quick answers
Will the BLUETTI PV350D work with the Goal Zero Yeti 1500X?
Yes. One BLUETTI PV350D works with the Goal Zero Yeti 1500X: about 36.1 V on a 20°F morning against the station's 50 V limit, and about 350 W in full sun. Two panels: works (2 panels in parallel on High Power Port), about 600 W.
Can I connect two PV350D panels to the Yeti 1500X?
Yes, 2 panels in parallel on High Power Port. That gives about 600 W.
What cable do I need to connect the PV350D to the Yeti 1500X?
The panel's plug type is not confirmed yet. Check the label or the box before buying a cable.
Is it safe on a cold morning?
Panel voltage rises in the cold. One PV350D goes from 33 V on its label to about 36.1 V at 20°F and 37.2 V at 0°F. The Yeti 1500X accepts up to 50 V on the High Power Port.
Where to buy
We may earn a commission if you buy through these links. It never changes a verdict.
Other panels that work with the Yeti 1500X
- Goal Zero Yeti 1500X: solar input 14 to 50 V on the Solar in 1 (High Power Port). Goal Zero does not say whether this limit is open-circuit or working voltage, so we use the stricter reading: open-circuit voltage on your coldest morning.
- Cold raises panel voltage: we add 0.30% per °C below 77F (25°C), a typical figure, since this panel does not publish its own. At 20F one panel's 33 V becomes 36.1 V.
- Current over the 50 A cap is safe: the station takes 50 A and you get fewer watts. We count only the capped watts.
- Max 600 W on this input, 600 W across all inputs.
- Cold-morning voltage uses 0.30% per °C, typical for crystalline panels. This panel's own value is not published.
- Expected watts are the best case in full sun. Real-world midday output is usually 60 to 80% of that.