Will the Anker SOLIX PS400 Bifacial work with the BLUETTI AC200L?
Yes. One Anker SOLIX PS400 Bifacial works with the BLUETTI AC200L: about 63.1 V on a 20°F morning against the station's 145 V limit, and about 400 W in full sun. Two panels: works (2 panels in series on DC input (via DC input cable + solar charging cable)), about 800 W.
Works
1 x PS400 Bifacial into the AC200L (1 panel on DC input (via DC input cable + solar charging cable)) stays inside 12 to 145 V and under 15 A, even at 20F.
- BLUETTI's manual says to wire the panels in series. With a 145V limit, the AC200L takes far longer strings than the 60V stations.
- Use at least 100W of panels.
- 57.6 V open circuit: above the 55-60 V limit of many smaller stations even as a single panel on a cold morning.
- Use the solar charging cable that came with the station (MC4 on the panel side).
400 W, open-circuit 57.6 V, short-circuit 8.8 A, working 48 V / 8.3 A. Unconfirmed Panel details
BLUETTI AC200LSolar input DC input (via DC input cable + solar charging cable): 12 to 145 V, 1200 W max. Manual Station details
Change the count or temperatureTwo panels: every way to wire them
| Wiring | Input | Volts at 20F | Amps | Watts | Verdict |
|---|---|---|---|---|---|
| 2 panels in series on DC input (via DC input cable + solar charging cable) Best option | DC input (via DC input cable + solar charging cable) | 126.1 | 8.3 | 800 | Works |
| 2 panels in parallel on DC input (via DC input cable + solar charging cable) The panels can push 16.7A but this input takes 15A, so the station caps it. Safe, you just lose some watts. | DC input (via DC input cable + solar charging cable) | 63.1 | 16.7 | 720 | Works |
Quick answers
Will the Anker SOLIX PS400 Bifacial work with the BLUETTI AC200L?
Yes. One Anker SOLIX PS400 Bifacial works with the BLUETTI AC200L: about 63.1 V on a 20°F morning against the station's 145 V limit, and about 400 W in full sun. Two panels: works (2 panels in series on DC input (via DC input cable + solar charging cable)), about 800 W.
Can I connect two PS400 Bifacial panels to the AC200L?
Yes, 2 panels in series on DC input (via DC input cable + solar charging cable). That gives about 800 W.
What cable do I need to connect the PS400 Bifacial to the AC200L?
Use the solar charging cable that came with the station (MC4 on the panel side).
Is it safe on a cold morning?
Panel voltage rises in the cold. One PS400 Bifacial goes from 57.6 V on its label to about 63.1 V at 20°F and 65 V at 0°F. The AC200L accepts up to 145 V on the DC input (via DC input cable + solar charging cable).
Where to buy
We may earn a commission if you buy through these links. It never changes a verdict.
Other panels that work with the AC200L
- BLUETTI AC200L: solar input 12 to 145 V on the Solar in (DC input (via DC input cable + solar charging cable)). BLUETTI sets this limit on open-circuit voltage (Voc), so we hold the panels' Voc on your coldest morning to it.
- Cold raises panel voltage: we add 0.30% per °C below 77F (25°C), a typical figure, since this panel does not publish its own. At 20F one panel's 57.6 V becomes 63.1 V.
- Current over the 15 A cap is safe: the station takes 15 A and you get fewer watts. We count only the capped watts.
- Max 1,200 W on this input.
- Cold-morning voltage uses 0.30% per °C, typical for crystalline panels. This panel's own value is not published.
- Expected watts are the best case in full sun. Real-world midday output is usually 60 to 80% of that.
- Some numbers for Anker SOLIX PS400 Bifacial come from a shop listing we have not confirmed in the manual yet.