Will the EcoFlow NextGen 220W Bifacial Portable Solar Panel work with the Anker SOLIX C300 DC?
Yes. One EcoFlow NextGen 220W Bifacial Portable Solar Panel works with the Anker SOLIX C300 DC: about 23.5 V on a 20°F morning against the station's 28 V limit, and about 100 W in full sun. Two panels: works (2 panels in parallel on XT60), about 100 W.
Works
1 x NextGen 220W Bifacial Portable Solar Panel into the C300 DC (1 panel on XT60) stays inside 11 to 28 V, even at 20F. The station caps the current at 8.2 A.
- The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number.
- The panels can push 11.9A but this input takes 8.2A, so the station caps it. Safe, you just lose some watts.
- Anker's manual: the panel voltage must be 11 to 28V or the station can be damaged.
- Use an MC4 to XT60 solar cable.
220 W, open-circuit 21.5 V, short-circuit 12.4 A, working 18.4 V / 11.9 A. Brand page Panel details
Anker SOLIX C300 DCSolar input XT60: 11 to 28 V, 100 W max. Manual Station details
Change the count or temperatureTwo panels: every way to wire them
| Wiring | Input | Volts at 20F | Amps | Watts | Verdict |
|---|---|---|---|---|---|
| 2 panels in parallel on XT60 The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number. | XT60 | 23.5 | 23.8 | 100 | Works |
| 2 panels in series on XT60 Open-circuit voltage 43V is above the station's 28V limit. Going over a station's input voltage limit can damage it. | XT60 | 47.1 | 11.9 | 0 | Don't connect |
Quick answers
Will the EcoFlow NextGen 220W Bifacial Portable Solar Panel work with the Anker SOLIX C300 DC?
Yes. One EcoFlow NextGen 220W Bifacial Portable Solar Panel works with the Anker SOLIX C300 DC: about 23.5 V on a 20°F morning against the station's 28 V limit, and about 100 W in full sun. Two panels: works (2 panels in parallel on XT60), about 100 W.
Can I connect two NextGen 220W Bifacial Portable Solar Panel panels to the C300 DC?
Yes, 2 panels in parallel on XT60. That gives about 100 W.
What cable do I need to connect the NextGen 220W Bifacial Portable Solar Panel to the C300 DC?
Use an MC4 to XT60 solar cable.
Is it safe on a cold morning?
Panel voltage rises in the cold. One NextGen 220W Bifacial Portable Solar Panel goes from 21.5 V on its label to about 23.5 V at 20°F and 24.3 V at 0°F. The C300 DC accepts up to 28 V on the XT60.
Where to buy
We may earn a commission if you buy through these links. It never changes a verdict.
Other panels that work with the C300 DC
- Anker SOLIX C300 DC: solar input 11 to 28 V on the Solar in (XT60). Anker SOLIX does not say whether this limit is open-circuit or working voltage, so we use the stricter reading: open-circuit voltage on your coldest morning.
- Cold raises panel voltage: we add 0.30% per °C below 77F (25°C), a typical figure, since this panel does not publish its own. At 20F one panel's 21.5 V becomes 23.5 V.
- Current over the 8.2 A cap is safe: the station takes 8.2 A and you get fewer watts. We count only the capped watts.
- Max 100 W on this input.
- Cold-morning voltage uses 0.30% per °C, typical for crystalline panels. This panel's own value is not published.
- Expected watts are the best case in full sun. Real-world midday output is usually 60 to 80% of that.