Will the EcoFlow NextGen 220W Bifacial Portable Solar Panel work with the Anker SOLIX C1000X?
Yes. One EcoFlow NextGen 220W Bifacial Portable Solar Panel works with the Anker SOLIX C1000X: about 23.5 V on a 20°F morning against the station's 60 V limit, and about 184 W in full sun. Two panels: works (2 panels in series on XT60), about 438 W.
Works
1 x NextGen 220W Bifacial Portable Solar Panel into the C1000X (1 panel on XT60) stays inside 11 to 60 V, even at 20F. The station caps the current at 10 A.
- The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number.
- The panels can push 11.9A but this input takes 10A, so the station caps it. Safe, you just lose some watts.
- Anker does not say whether its voltage limit is open-circuit or working voltage, so the checker uses the stricter reading.
- Below 32V the input takes 10A; from 32 to 60V it takes 12.5A.
- Use an MC4 to XT60 solar cable.
220 W, open-circuit 21.5 V, short-circuit 12.4 A, working 18.4 V / 11.9 A. Brand page Panel details
Anker SOLIX C1000XSolar input XT60: 11 to 60 V, 600 W max. Brand page Station details
Change the count or temperatureTwo panels: every way to wire them
| Wiring | Input | Volts at 20F | Amps | Watts | Verdict |
|---|---|---|---|---|---|
| 2 panels in series on XT60 The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number. | XT60 | 47.1 | 11.9 | 438 | Works |
| 2 panels in parallel on XT60 The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number. | XT60 | 23.5 | 23.8 | 184 | Works |
Quick answers
Will the EcoFlow NextGen 220W Bifacial Portable Solar Panel work with the Anker SOLIX C1000X?
Yes. One EcoFlow NextGen 220W Bifacial Portable Solar Panel works with the Anker SOLIX C1000X: about 23.5 V on a 20°F morning against the station's 60 V limit, and about 184 W in full sun. Two panels: works (2 panels in series on XT60), about 438 W.
Can I connect two NextGen 220W Bifacial Portable Solar Panel panels to the C1000X?
Yes, 2 panels in series on XT60. That gives about 438 W.
What cable do I need to connect the NextGen 220W Bifacial Portable Solar Panel to the C1000X?
Use an MC4 to XT60 solar cable.
Is it safe on a cold morning?
Panel voltage rises in the cold. One NextGen 220W Bifacial Portable Solar Panel goes from 21.5 V on its label to about 23.5 V at 20°F and 24.3 V at 0°F. The C1000X accepts up to 60 V on the XT60.
Where to buy
We may earn a commission if you buy through these links. It never changes a verdict.
Other panels that work with the C1000X
- Anker SOLIX C1000X: solar input 11 to 60 V on the Solar in (XT60). Anker SOLIX does not say whether this limit is open-circuit or working voltage, so we use the stricter reading: open-circuit voltage on your coldest morning.
- Cold raises panel voltage: we add 0.30% per °C below 77F (25°C), a typical figure, since this panel does not publish its own. At 20F one panel's 21.5 V becomes 23.5 V.
- Current over the 10 A cap is safe: the station takes 10 A and you get fewer watts. We count only the capped watts.
- Max 600 W on this input.
- Cold-morning voltage uses 0.30% per °C, typical for crystalline panels. This panel's own value is not published.
- Expected watts are the best case in full sun. Real-world midday output is usually 60 to 80% of that.