Will the Renogy 200W N-Type Solar Panel work with the Anker SOLIX C1000X Gen 2?
Yes. One Renogy 200W N-Type Solar Panel works with the Anker SOLIX C1000X Gen 2: about 25.2 V on a 20°F morning against the station's 60 V limit, and about 157 W in full sun. Two panels: works (2 panels in series on XT60i), about 400 W.
Works
1 x 200W N-Type Solar Panel into the C1000X Gen 2 (1 panel on XT60i) stays inside 11 to 60 V, even at 20F. The station caps the current at 8.2 A.
- The panels can push 10.4A but this input takes 8.2A, so the station caps it. Safe, you just lose some watts.
- Anker: keep the total open-circuit voltage within 60 V and the total short-circuit current within 15 A, and wire several panels in parallel, not in series.
- Use an MC4 to XT60i solar cable.
200 W, open-circuit 23 V, short-circuit 11.1 A, working 19.2 V / 10.4 A. Brand page Panel details
Anker SOLIX C1000X Gen 2Solar input XT60i: 11 to 60 V, 600 W max. Manual Station details
Change the count or temperatureTwo panels: every way to wire them
| Wiring | Input | Volts at 20F | Amps | Watts | Verdict |
|---|---|---|---|---|---|
| 2 panels in series on XT60i Best option | XT60i | 50.4 | 10.4 | 400 | Works |
| 2 panels in parallel on XT60i The panels can push 20.8A but this input takes 8.2A, so the station caps it. Safe, you just lose some watts. | XT60i | 25.2 | 20.8 | 157 | Works |
Quick answers
Will the Renogy 200W N-Type Solar Panel work with the Anker SOLIX C1000X Gen 2?
Yes. One Renogy 200W N-Type Solar Panel works with the Anker SOLIX C1000X Gen 2: about 25.2 V on a 20°F morning against the station's 60 V limit, and about 157 W in full sun. Two panels: works (2 panels in series on XT60i), about 400 W.
Can I connect two 200W N-Type Solar Panel panels to the C1000X Gen 2?
Yes, 2 panels in series on XT60i. That gives about 400 W.
What cable do I need to connect the 200W N-Type Solar Panel to the C1000X Gen 2?
Use an MC4 to XT60i solar cable.
Is it safe on a cold morning?
Panel voltage rises in the cold. One 200W N-Type Solar Panel goes from 23 V on its label to about 25.2 V at 20°F and 26 V at 0°F. The C1000X Gen 2 accepts up to 60 V on the XT60i.
Where to buy
We may earn a commission if you buy through these links. It never changes a verdict.
Other panels that work with the C1000X Gen 2
- Anker SOLIX C1000X Gen 2: solar input 11 to 60 V on the Solar in (XT60i). Anker SOLIX sets this limit on open-circuit voltage (Voc), so we hold the panels' Voc on your coldest morning to it.
- Cold raises panel voltage: we add 0.30% per °C below 77F (25°C), a typical figure, since this panel does not publish its own. At 20F one panel's 23 V becomes 25.2 V.
- Current over the 8.2 A cap is safe: the station takes 8.2 A and you get fewer watts. We count only the capped watts.
- Max 600 W on this input.
- Cold-morning voltage uses 0.30% per °C, typical for crystalline panels. This panel's own value is not published.
- Expected watts are the best case in full sun. Real-world midday output is usually 60 to 80% of that.