Will the EcoFlow 175W Rigid Solar Panel work with the Anker SOLIX C1000X Gen 2?
Yes. One EcoFlow 175W Rigid Solar Panel works with the Anker SOLIX C1000X Gen 2: about 27.9 V on a 20°F morning against the station's 60 V limit, and about 175 W in full sun. Two panels: works (2 panels in series on XT60i), about 350 W.
Works
1 x 175W Rigid Solar Panel into the C1000X Gen 2 (1 panel on XT60i) stays inside 11 to 60 V and under 8.2 A, even at 20F.
- Anker: keep the total open-circuit voltage within 60 V and the total short-circuit current within 15 A, and wire several panels in parallel, not in series.
- EcoFlow's spec table labels the 7.85 A figure as a voltage; it is the operating current.
- Use an MC4 to XT60i solar cable.
175 W, open-circuit 25.5 V, short-circuit 8.3 A, working 22.3 V / 7.9 A. Brand page Panel details
Anker SOLIX C1000X Gen 2Solar input XT60i: 11 to 60 V, 600 W max. Manual Station details
Change the count or temperatureTwo panels: every way to wire them
| Wiring | Input | Volts at 20F | Amps | Watts | Verdict |
|---|---|---|---|---|---|
| 2 panels in series on XT60i Best option | XT60i | 55.8 | 7.9 | 350 | Works |
| 2 panels in parallel on XT60i The panels can push 15.7A but this input takes 8.2A, so the station caps it. Safe, you just lose some watts. | XT60i | 27.9 | 15.7 | 183 | Works |
Quick answers
Will the EcoFlow 175W Rigid Solar Panel work with the Anker SOLIX C1000X Gen 2?
Yes. One EcoFlow 175W Rigid Solar Panel works with the Anker SOLIX C1000X Gen 2: about 27.9 V on a 20°F morning against the station's 60 V limit, and about 175 W in full sun. Two panels: works (2 panels in series on XT60i), about 350 W.
Can I connect two 175W Rigid Solar Panel panels to the C1000X Gen 2?
Yes, 2 panels in series on XT60i. That gives about 350 W.
What cable do I need to connect the 175W Rigid Solar Panel to the C1000X Gen 2?
Use an MC4 to XT60i solar cable.
Is it safe on a cold morning?
Panel voltage rises in the cold. One 175W Rigid Solar Panel goes from 25.5 V on its label to about 27.9 V at 20°F and 28.8 V at 0°F. The C1000X Gen 2 accepts up to 60 V on the XT60i.
Where to buy
We may earn a commission if you buy through these links. It never changes a verdict.
Other panels that work with the C1000X Gen 2
- Anker SOLIX C1000X Gen 2: solar input 11 to 60 V on the Solar in (XT60i). Anker SOLIX sets this limit on open-circuit voltage (Voc), so we hold the panels' Voc on your coldest morning to it.
- Cold raises panel voltage: we add 0.30% per °C below 77F (25°C), a typical figure, since this panel does not publish its own. At 20F one panel's 25.5 V becomes 27.9 V.
- Current over the 8.2 A cap is safe: the station takes 8.2 A and you get fewer watts. We count only the capped watts.
- Max 600 W on this input.
- Cold-morning voltage uses 0.30% per °C, typical for crystalline panels. This panel's own value is not published.
- Expected watts are the best case in full sun. Real-world midday output is usually 60 to 80% of that.