Will the BLUETTI PV350D work with the Anker SOLIX C1000X Gen 2?
Yes. One BLUETTI PV350D works with the Anker SOLIX C1000X Gen 2: about 36.1 V on a 20°F morning against the station's 60 V limit, and about 226 W in full sun. Two panels: works (2 panels in parallel on XT60i), about 226 W.
Works
1 x PV350D into the C1000X Gen 2 (1 panel on XT60i) stays inside 11 to 60 V, even at 20F. The station caps the current at 8.2 A.
- The panels can push 12.7A but this input takes 8.2A, so the station caps it. Safe, you just lose some watts.
- Anker: keep the total open-circuit voltage within 60 V and the total short-circuit current within 15 A, and wire several panels in parallel, not in series.
- The panel's plug type is not confirmed yet. Check the label or the box before buying a cable.
350 W, open-circuit 33 V, short-circuit 13.8 A, working 27.6 V / 12.7 A. Manual Panel details
Anker SOLIX C1000X Gen 2Solar input XT60i: 11 to 60 V, 600 W max. Manual Station details
Change the count or temperatureTwo panels: every way to wire them
| Wiring | Input | Volts at 20F | Amps | Watts | Verdict |
|---|---|---|---|---|---|
| 2 panels in parallel on XT60i The panels can push 25.4A but this input takes 8.2A, so the station caps it. Safe, you just lose some watts. | XT60i | 36.1 | 25.4 | 226 | Works |
| 2 panels in series on XT60i Open-circuit voltage 66V is above the station's 60V limit. Going over a station's input voltage limit can damage it. | XT60i | 72.3 | 12.7 | 0 | Don't connect |
Quick answers
Will the BLUETTI PV350D work with the Anker SOLIX C1000X Gen 2?
Yes. One BLUETTI PV350D works with the Anker SOLIX C1000X Gen 2: about 36.1 V on a 20°F morning against the station's 60 V limit, and about 226 W in full sun. Two panels: works (2 panels in parallel on XT60i), about 226 W.
Can I connect two PV350D panels to the C1000X Gen 2?
Yes, 2 panels in parallel on XT60i. That gives about 226 W.
What cable do I need to connect the PV350D to the C1000X Gen 2?
The panel's plug type is not confirmed yet. Check the label or the box before buying a cable.
Is it safe on a cold morning?
Panel voltage rises in the cold. One PV350D goes from 33 V on its label to about 36.1 V at 20°F and 37.2 V at 0°F. The C1000X Gen 2 accepts up to 60 V on the XT60i.
Where to buy
We may earn a commission if you buy through these links. It never changes a verdict.
Other panels that work with the C1000X Gen 2
- Anker SOLIX C1000X Gen 2: solar input 11 to 60 V on the Solar in (XT60i). Anker SOLIX sets this limit on open-circuit voltage (Voc), so we hold the panels' Voc on your coldest morning to it.
- Cold raises panel voltage: we add 0.30% per °C below 77F (25°C), a typical figure, since this panel does not publish its own. At 20F one panel's 33 V becomes 36.1 V.
- Current over the 8.2 A cap is safe: the station takes 8.2 A and you get fewer watts. We count only the capped watts.
- Max 600 W on this input.
- Cold-morning voltage uses 0.30% per °C, typical for crystalline panels. This panel's own value is not published.
- Expected watts are the best case in full sun. Real-world midday output is usually 60 to 80% of that.