Will the BLUETTI PV350D work with the Jackery Explorer 1000 v2?
Yes. One BLUETTI PV350D works with the Jackery Explorer 1000 v2: about 36.1 V on a 20°F morning against the station's 60 V limit, and about 290 W in full sun. Two panels: works (1 panel on DC8020 + 1 panel on DC8020), about 400 W.
Works
1 x PV350D into the Explorer 1000 v2 (1 panel on DC8020) stays inside 12 to 60 V, even at 20F. The station caps the current at 10.5 A.
- The panels can push 12.7A but this input takes 10.5A, so the station caps it. Safe, you just lose some watts.
- Jackery's manual: each of the two DC8020 ports takes one 100W or 200W panel directly. Two 100W panels on one port need Jackery's solar panel connector.
- Below 16V working voltage each port only takes 8A instead of 10.5A.
- The panel's plug type is not confirmed yet. Check the label or the box before buying a cable.
350 W, open-circuit 33 V, short-circuit 13.8 A, working 27.6 V / 12.7 A. Manual Panel details
Jackery Explorer 1000 v2Solar input DC8020: 12 to 60 V; DC8020: 12 to 60 V, 400 W max. Manual Station details
Change the count or temperatureTwo panels: every way to wire them
| Wiring | Input | Volts at 20F | Amps | Watts | Verdict |
|---|---|---|---|---|---|
| 1 panel on DC8020 + 1 panel on DC8020 The panels can push 12.7A but this input takes 10.5A, so the station caps it. Safe, you just lose some watts. | DC8020 + DC8020 | 36.1 | 12.7 | 400 | Works |
| 2 panels in parallel on DC8020 The panels can push 25.4A but this input takes 10.5A, so the station caps it. Safe, you just lose some watts. | DC8020 | 36.1 | 25.4 | 290 | Works |
| 2 panels in series on DC8020 The panels' open-circuit voltage (66V) is above 60V. The manual only rates working voltage, so this is outside what the manual covers. | DC8020 | 72.3 | 12.7 | 400 | Works, with a catch |
Quick answers
Will the BLUETTI PV350D work with the Jackery Explorer 1000 v2?
Yes. One BLUETTI PV350D works with the Jackery Explorer 1000 v2: about 36.1 V on a 20°F morning against the station's 60 V limit, and about 290 W in full sun. Two panels: works (1 panel on DC8020 + 1 panel on DC8020), about 400 W.
Can I connect two PV350D panels to the Explorer 1000 v2?
Yes, 1 panel on DC8020 + 1 panel on DC8020. That gives about 400 W.
What cable do I need to connect the PV350D to the Explorer 1000 v2?
The panel's plug type is not confirmed yet. Check the label or the box before buying a cable.
Is it safe on a cold morning?
Panel voltage rises in the cold. One PV350D goes from 33 V on its label to about 36.1 V at 20°F and 37.2 V at 0°F. The Explorer 1000 v2 accepts up to 60 V on the DC8020.
Where to buy
We may earn a commission if you buy through these links. It never changes a verdict.
Other panels that work with the Explorer 1000 v2
- Jackery Explorer 1000 v2: solar input 12 to 60 V on the Solar in 1 (DC8020). Jackery rates this input by working voltage (Vmp), so that is the number we hold to the limit. We still warn when the cold-morning open-circuit voltage goes over it.
- Cold raises panel voltage: we add 0.30% per °C below 77F (25°C), a typical figure, since this panel does not publish its own. At 20F one panel's 33 V becomes 36.1 V.
- Current over the 10.5 A cap is safe: the station takes 10.5 A and you get fewer watts. We count only the capped watts.
- Max 200 W on this input, 400 W across all inputs.
- Cold-morning voltage uses 0.30% per °C, typical for crystalline panels. This panel's own value is not published.
- Expected watts are the best case in full sun. Real-world midday output is usually 60 to 80% of that.