Will the BLUETTI PV100 FX Flexible Solar Panel work with the Anker SOLIX F2600?
Yes. One BLUETTI PV100 FX Flexible Solar Panel works with the Anker SOLIX F2600: about 45.3 V on a 20°F morning against the station's 60 V limit, and about 100 W in full sun. Two panels: works (2 panels in parallel on Solar input), about 200 W.
Works
1 x PV100 FX Flexible Solar Panel into the F2600 (1 panel on Solar input) stays inside 11 to 60 V and under 20 A, even at 20F.
- The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number.
- Anker does not say whether its voltage limit is open-circuit or working voltage, so the checker uses the stricter reading.
- 41.4 V open circuit is high for a 100 W panel: two in series reach 82.8 V, more than most stations take.
- The BLUETTI US store sells it only in sets of 2 or more.
- Use the solar charging cable that came with the station (MC4 on the panel side).
100 W, open-circuit 41.4 V, short-circuit 3.1 A. Brand page Panel details
Anker SOLIX F2600Solar input Solar input: 11 to 60 V, 1000 W max. Brand page Station details
Change the count or temperatureTwo panels: every way to wire them
| Wiring | Input | Volts at 20F | Amps | Watts | Verdict |
|---|---|---|---|---|---|
| 2 panels in parallel on Solar input The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number. | Solar input | 45.3 | 6.1 | 200 | Works |
| 2 panels in series on Solar input Open-circuit voltage 82.8V is above the station's 60V limit. Going over a station's input voltage limit can damage it. | Solar input | 90.7 | 3.1 | 0 | Don't connect |
Quick answers
Will the BLUETTI PV100 FX Flexible Solar Panel work with the Anker SOLIX F2600?
Yes. One BLUETTI PV100 FX Flexible Solar Panel works with the Anker SOLIX F2600: about 45.3 V on a 20°F morning against the station's 60 V limit, and about 100 W in full sun. Two panels: works (2 panels in parallel on Solar input), about 200 W.
Can I connect two PV100 FX Flexible Solar Panel panels to the F2600?
Yes, 2 panels in parallel on Solar input. That gives about 200 W.
What cable do I need to connect the PV100 FX Flexible Solar Panel to the F2600?
Use the solar charging cable that came with the station (MC4 on the panel side).
Is it safe on a cold morning?
Panel voltage rises in the cold. One PV100 FX Flexible Solar Panel goes from 41.4 V on its label to about 45.3 V at 20°F and 46.7 V at 0°F. The F2600 accepts up to 60 V on the Solar input.
Where to buy
We may earn a commission if you buy through these links. It never changes a verdict.
Other panels that work with the F2600
- Anker SOLIX F2600: solar input 11 to 60 V on the Solar in (Solar input). Anker SOLIX does not say whether this limit is open-circuit or working voltage, so we use the stricter reading: open-circuit voltage on your coldest morning.
- Cold raises panel voltage: we add 0.30% per °C below 77F (25°C), a typical figure, since this panel does not publish its own. At 20F one panel's 41.4 V becomes 45.3 V.
- Current over the 20 A cap is safe: the station takes 20 A and you get fewer watts. We count only the capped watts.
- Max 1,000 W on this input.
- Cold-morning voltage uses 0.30% per °C, typical for crystalline panels. This panel's own value is not published.
- Expected watts are the best case in full sun. Real-world midday output is usually 60 to 80% of that.