Will the Jackery SolarSaga 200 (JS-200D) work with the Anker SOLIX F1500?
Yes. One Jackery SolarSaga 200 (JS-200D) works with the Anker SOLIX F1500: about 26.9 V on a 20°F morning against the station's 30 V limit, and about 200 W in full sun. Two panels: works (2 panels in parallel on XT60), about 250 W.
Works
1 x SolarSaga 200 (JS-200D) into the F1500 (1 panel on XT60) stays inside 11 to 30 V and under 12.5 A, even at 20F.
- The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number.
- Anker does not say whether its voltage limit is open-circuit or working voltage, so the checker uses the stricter reading.
- Anker's own page gives two different solar limits for this model (up to 30V and up to 60V). Until that is settled, the checker uses 30V.
- Needs a DC8020 to XT60 adapter. Neither brand sells this pairing, so check any third-party adapter is rated for the current.
200 W, open-circuit 24.8 V, short-circuit 11.2 A, working 20 V / 10 A. Manual Panel details
Anker SOLIX F1500Solar input XT60: 11 to 30 V, 600 W max. Brand page Station details
Change the count or temperatureTwo panels: every way to wire them
| Wiring | Input | Volts at 20F | Amps | Watts | Verdict |
|---|---|---|---|---|---|
| 2 panels in parallel on XT60 The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number. | XT60 | 26.9 | 20 | 250 | Works |
| 2 panels in series on XT60 Open-circuit voltage 49.6V is above the station's 30V limit. Going over a station's input voltage limit can damage it. | XT60 | 53.8 | 10 | 0 | Don't connect |
Quick answers
Will the Jackery SolarSaga 200 (JS-200D) work with the Anker SOLIX F1500?
Yes. One Jackery SolarSaga 200 (JS-200D) works with the Anker SOLIX F1500: about 26.9 V on a 20°F morning against the station's 30 V limit, and about 200 W in full sun. Two panels: works (2 panels in parallel on XT60), about 250 W.
Can I connect two SolarSaga 200 (JS-200D) panels to the F1500?
Yes, 2 panels in parallel on XT60. That gives about 250 W.
What cable do I need to connect the SolarSaga 200 (JS-200D) to the F1500?
Needs a DC8020 to XT60 adapter. Neither brand sells this pairing, so check any third-party adapter is rated for the current.
Is it safe on a cold morning?
Panel voltage rises in the cold. One SolarSaga 200 (JS-200D) goes from 24.8 V on its label to about 26.9 V at 20°F and 27.6 V at 0°F. The F1500 accepts up to 30 V on the XT60.
Where to buy
We may earn a commission if you buy through these links. It never changes a verdict.
Other panels that work with the F1500
- Anker SOLIX F1500: solar input 11 to 30 V on the Solar in (XT60). Anker SOLIX does not say whether this limit is open-circuit or working voltage, so we use the stricter reading: open-circuit voltage on your coldest morning.
- Cold raises panel voltage: we add 0.27% per °C below 77F (25°C), this panel's own figure. At 20F one panel's 24.8 V becomes 26.9 V.
- Current over the 12.5 A cap is safe: the station takes 12.5 A and you get fewer watts. We count only the capped watts.
- Max 600 W on this input.
- Cold-morning voltage uses this panel's own coefficient from its manual, 0.27% per °C.
- Expected watts are the best case in full sun. Real-world midday output is usually 60 to 80% of that.