Will the Jackery SolarSaga 200 (JS-200E) work with the Anker SOLIX C200 DC?
Yes. One Jackery SolarSaga 200 (JS-200E) works with the Anker SOLIX C200 DC: about 23.9 V on a 20°F morning against the station's 28 V limit, and about 100 W in full sun. Two panels: works (2 panels in parallel on XT60), about 100 W.
Works
1 x SolarSaga 200 (JS-200E) into the C200 DC (1 panel on XT60) stays inside 11 to 28 V, even at 20F. The station caps the current at 8.2 A.
- The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number.
- The panels can push 11.5A but this input takes 8.2A, so the station caps it. Safe, you just lose some watts.
- Anker's manual: use only 11 to 28V panels with an XT60 plug. The PS200 and PS400 panels are not compatible and can damage it.
- Needs a DC8020 to XT60 adapter. Neither brand sells this pairing, so check any third-party adapter is rated for the current.
200 W, open-circuit 22 V, short-circuit 12.5 A, working 18 V / 11.5 A. Manual Panel details
Anker SOLIX C200 DCSolar input XT60: 11 to 28 V, 100 W max. Manual Station details
Change the count or temperatureTwo panels: every way to wire them
| Wiring | Input | Volts at 20F | Amps | Watts | Verdict |
|---|---|---|---|---|---|
| 2 panels in parallel on XT60 The brand does not say whether its voltage limit is open-circuit or working voltage, so we check against the stricter open-circuit number. | XT60 | 23.9 | 23 | 100 | Works |
| 2 panels in series on XT60 Open-circuit voltage 44V is above the station's 28V limit. Going over a station's input voltage limit can damage it. | XT60 | 47.8 | 11.5 | 0 | Don't connect |
Quick answers
Will the Jackery SolarSaga 200 (JS-200E) work with the Anker SOLIX C200 DC?
Yes. One Jackery SolarSaga 200 (JS-200E) works with the Anker SOLIX C200 DC: about 23.9 V on a 20°F morning against the station's 28 V limit, and about 100 W in full sun. Two panels: works (2 panels in parallel on XT60), about 100 W.
Can I connect two SolarSaga 200 (JS-200E) panels to the C200 DC?
Yes, 2 panels in parallel on XT60. That gives about 100 W.
What cable do I need to connect the SolarSaga 200 (JS-200E) to the C200 DC?
Needs a DC8020 to XT60 adapter. Neither brand sells this pairing, so check any third-party adapter is rated for the current.
Is it safe on a cold morning?
Panel voltage rises in the cold. One SolarSaga 200 (JS-200E) goes from 22 V on its label to about 23.9 V at 20°F and 24.5 V at 0°F. The C200 DC accepts up to 28 V on the XT60.
Where to buy
We may earn a commission if you buy through these links. It never changes a verdict.
Other panels that work with the C200 DC
- Anker SOLIX C200 DC: solar input 11 to 28 V on the Solar in (XT60). Anker SOLIX does not say whether this limit is open-circuit or working voltage, so we use the stricter reading: open-circuit voltage on your coldest morning.
- Cold raises panel voltage: we add 0.27% per °C below 77F (25°C), this panel's own figure. At 20F one panel's 22 V becomes 23.9 V.
- Current over the 8.2 A cap is safe: the station takes 8.2 A and you get fewer watts. We count only the capped watts.
- Max 100 W on this input.
- Cold-morning voltage uses this panel's own coefficient from its manual, 0.27% per °C.
- Expected watts are the best case in full sun. Real-world midday output is usually 60 to 80% of that.